 | OTS – dotyková sonda pro nastavování nástrojů
Tato stránka není v současné době k dispozici ve vašem jazyce. Automatizovaný překlad můžete zobrazit pomocí nástroje Google Translate. Neodpovídáme za poskytování této služby a výsledky překladu jsme nekontrolovali.
Potřebujete-li další pomoc, kontaktujte nás.
 OTS cableless optical tool setting and broken tool detection for vertical machining centres.
The OTS can be used as part of a twin probe system, either with a second OTS (e.g. on machines with twin pallets), or with a suitable inspection probe. About OTS |  For broken tool detection and rapid tool length/diameter measurement use the OTS, Renishaw's first tool setting probe with optical transmission. The robust, compact and cable-free design allows freedom of table movement, ideal for twin pallet or rotary table machines.
The OTS is available in two versions, one with 1/2 AA batteries and the other with AA batteries. This allows the use of the same battery type in the OTS as the spindle probe. |  The OTS uses the OMI-2T optical interface for twin probing (or single probe use) and the OMI-2 for single installations only. | OTS features and benefits
 Optical tool setting probe - no cables- Compact table mounting, ideal for twin pallet or rotary table machines
- Precise tool length and diameter measurement
- Automated updating of tool offsets
OTS specification | Sense directions | ±X, ±Y, +Z | | Weight 1/2 AA AA | 450 g (16 oz) 490 g (18 oz) | | Transmission type | Infra-red optical transmission | Uni-directional repeatability
(max 2 sigma at stylus tip) | 1.0 µm (0.00004 in) | | Trigger force Lowest force Highest force | 1.3 N (4.6 ozf) 2.4 N (8.5 ozf) | | Stylus overtravel XY plane +Z direction | ±3.5 mm (0.14 in) 6 mm (0.23 in) | | Sealing | IP X8 | | Mounting | 12.7/10 mm (0.5/0.39 in) caphead bolt (not supplied). Optional spiral pins to allow accurate re-mounting. | | Compatible interface | OMI-2T/OMI-2 | Software for OTS Renishaw tool setting software allows you to set tool length and diameter offsets for single point and multiple point tools, perform in cycle broken tool detection and manual or automatic updates. Alternative tool setters | NC4 Non-contact tool setting and broken tool detection | | TRS2 Rapid non-contact broken tool detection | | TS27R Contact tool setting and broken tool detection | | 
Compact design is ideal for machines previously unsuitable for large non-contact systems | | 
A single sided device that recognises the presence of a rotating tool, typically in less than 1 second. | | 
The standard tool setting probe for machining centres | Order information
| Type |
Part number |
Description |
| OTS (1/2 AA) |
A-5401-2001 |
OTS probe with disc stylus, 1/2 AA batteries, tool kit and Quick-start guide. Set to: optical on/optical off/filter off/Probe 2 start/standard power. |
| OTS (1/2 AA) |
A-5401-2011 |
OTS probe with square stylus, 1/2 AA batteries, tool kit and Quick-start guide. Set to: optical on/optical off/filter off/Probe 2 start/standard power. |
| OTS (AA) |
A-5514-2001 |
OTS probe with disc stylus, AA batteries, tool kit and Quick-start guide. Set to: optical on/optical off/filter off/Probe 2 start/standard power. |
| OTS (AA) |
A-5514-2011 |
OTS probe with square stylus, AA batteries, tool kit and Quick-start guide. Set to: optical on/optical off/filter off/Probe 2 start/standard power. | |