Navigation
- CMM knowledgebase
- 3-axis systems
- Scanning probe systems
- SP80 / SP80H
- SP80 and SP80H installation and integration guide
- General information
- Product compliance
- System requirements
- Safety
- System interconnection and electrical integration
- Probe connector pin-outs
- Connecting the IU80 interpolator unit
- IU80 features and LEDs
- SP80 LED control
- Connecting SP80 / SP80H using the KM80 or KM6080
- Connecting SP80 / SP80H using the SM80
- Connecting SP80 / SP80H using UCC PI 80
- Connecting SP80 / SP80H to IU80 and CC6
- Connecting SP80 / SP80H to IU80 and OEM counter card
- Air supply
- Installing SP80 / SP80H air purge option
- Attaching the KM80 quill adaptor plate
- Alternative quill adaptor plates
- Aligning the KM80, KM6080 or SM80 for use with the SCP80(V)
- Mounting the SP80 / SP80H body to the quill adaptor plate
- Mounting / removing the SH80 / SH80K on the SP80 / SP80H body
- Mounting styli on the SH80 and styli orientation
- Fitting the SCP80 / SCP80V to the MRS / MRS2 rack system
- Alignment of the SCP80(V) to the CMM axes
- Establishing SCP80(V) port datums
- Put down and pick up routines for SH80
- Put down and pick up routine for SH80K with SP80
- Put down and pick up routine for SH80K with SP80H
- Modes of operation
- Maximising performance
- SP80 and SP80H stylus selection
- Maintenance
- SP80 and SP80H system integration notes
Navigation
- CMM knowledgebase
- 3-axis systems
- Scanning probe systems
- SP80 / SP80H
- SP80 and SP80H installation and integration guide
- General information
- Product compliance
- System requirements
- Safety
- System interconnection and electrical integration
- Probe connector pin-outs
- Connecting the IU80 interpolator unit
- IU80 features and LEDs
- SP80 LED control
- Connecting SP80 / SP80H using the KM80 or KM6080
- Connecting SP80 / SP80H using the SM80
- Connecting SP80 / SP80H using UCC PI 80
- Connecting SP80 / SP80H to IU80 and CC6
- Connecting SP80 / SP80H to IU80 and OEM counter card
- Air supply
- Installing SP80 / SP80H air purge option
- Attaching the KM80 quill adaptor plate
- Alternative quill adaptor plates
- Aligning the KM80, KM6080 or SM80 for use with the SCP80(V)
- Mounting the SP80 / SP80H body to the quill adaptor plate
- Mounting / removing the SH80 / SH80K on the SP80 / SP80H body
- Mounting styli on the SH80 and styli orientation
- Fitting the SCP80 / SCP80V to the MRS / MRS2 rack system
- Alignment of the SCP80(V) to the CMM axes
- Establishing SCP80(V) port datums
- Put down and pick up routines for SH80
- Put down and pick up routine for SH80K with SP80
- Put down and pick up routine for SH80K with SP80H
- Modes of operation
- Maximising performance
- SP80 and SP80H stylus selection
- Maintenance
- SP80 and SP80H system integration notes
Alignment of the SCP80(V) to the CMM axes
Alignment of the SCP80 to the CMM axes
The alignment of the SCP80 to the CMM axes should be checked to be within the limits shown below.
Alignment of the SCP80V to the CMM axes
The alignment of the SCP80V to the CMM axes should be checked to be within the limits shown below.
